USER MANUALEnglishPro2030
1213The Pro2030 has two compatible sensors for use with a field cable: Polarographic – This sensor has a black sensor body and is engraved
1415DO UNITSHighlight DO Units and press enter to open a submenu that allows you to select the dissolved oxygen units to be displayed on the Run scree
1617SPECIFIC CONDUCTANCE TEMPERATURE COEFFICIENT (SPC %/°C)SPC %/°C (Specific Conductance Temperature Coefficient) is the temperature coefficient used
1819RESETTING THE SYSTEM SETUP MENU TO FACTORY DEFAULTTo reset the Pro2030 settings to factory default, press the down arrow key while in the System
2021QUICK DO CALIBRATIONPerform this calibration procedure when Quick DO Calibration is enabled in the System Setup menu. Ensure the DO sensor has
2223CALIBRATING IN MG/L OR PPM Power the instrument on and place the sensor into a sample that has 1. been titrated to determine the dissolved
2425up the value of the solution at the current temperature and enter that value into the Pro2030. Most conductivity solutions are labeled with a valu
2627From the Run screen, use the up or down arrow keys to highlight the Save box and press enter to save the current readings. The instrument will ind
2829Figure 11, Erase data mode. Use the up or down arrow key to select Erase Data Set, Erase All Sets or the ESC-Exit function box, then press enter t
3031Before re-installing the DO sensor o-rings, make sure to use a clean workspace, clean hands and avoid contact with anything that may leave fibers
Item #605056Rev CDrawing # A605056November 2010©2010 YSI Incorporated.The YSI logo is a registered trademarks of YSI Incorporated. Teflon is a regist
3233Thread the cap membrane onto the sensor. It is normal for a small amount of electrolyte to overflow.Replace the sensor guard.Polarographic Sensor
3435Chemical cleaning: Remove the cap membrane and rinse the sensor with deionized or distilled water. Soak the sensing section of
3637to air dry completely. Next, use a new clean, dry cap membrane to screw over the sensor. This will keep the sensor dry and protect the anode and
3839Symptom Possible SolutionInstrument will not calibrate the Conductivity sensor; instrument displays “Calibration Over”, “Calibration Under”, or “U
4041ACCESSORIES / PART NUMBERSPart Number Description6052030 Pro2030 Instrument6262030-1, -4, -10, -20, or -30 1, 4, 10, 20, 30-meter cable assembly*6
4243RECYCLINGYSI is committed to reducing the environmental footprint in the course of doing business. Even though materials reduction is the ultimate
4445APPENDIX ADO% CALIBRATION VA LU E SCa librati on ValuePressureD.O. % in Hg mmHg kPa mbar101% 30.22 767.6 102.34 1023.38100% 29.92 760.0 101.33 10
46Temp °C Chlorinity : 0Salinity: 05.0 ppt9.0 ppt10.0 ppt18.1 ppt 15.0 ppt27.1 ppt20.0 ppt36.1 ppt25.0 ppt45.2 ppt26.0 8.11 7.71 7.33 6.96 6.62 6.2827
iLanguage ... 17Auto Shutoff ...
ii1THIS PAGE LEFT INTENTIONALLY BLANKINTRODUCTIONThank you for purchasing the YSI Pro2030, an instrument from the YSI Professional Series product fami
23Place the battery cover on the back of the instrument and tighten the 5. four screws. Do not over-tighten.Figure 1. Pro2030 with battery cover remo
45 Figure 3INSTALLING THE DISSOLVED OXYGEN SENSORThe Pro2030 has two compatible dissolved oxygen sensors: Polarographic – This sensor has a black sen
67light blue label on the bottle and Polarographic sensors utilize electrolyte with a white label on the bottle. The dissolved oxygen sensor is
89FIRST POWER ONThe instrument will step through an initial configuration when powered on for the first time. This will set the language, di
1011Example:Instrument #1 with DO Local% enabled:At 737 mmHg barometric pressure, roughly 841 ft above sea level, the instrument would calibrate to 10
Kommentare zu diesen Handbüchern